Home / Knowledge / Custom Shoe Box Guide: Construction, Board and Printing

Sourcing guide

Custom Shoe Box Guide: Construction, Board and Printing

How to specify a custom shoe box: lid-and-base, one-piece, drawer and carry-handle constructions, coated board or corrugated kraft, and the print finishes that change how a box looks and costs. Illustrated with boxes from real footwear orders.


A shoe box is specified once and then repeated on every pair you sell. The construction decides how it ships and stacks, the board decides what print it can carry, and the finish decides how it looks on a shelf or when it is unboxed. Changing any of these after the first production run is slow and expensive, so it pays to settle them at the sampling stage.

The photos in this guide are shoe boxes our partner packaging factory produced for DOING footwear clients. Brand names on the boxes belong to those clients and are shown only as examples of construction and print. You can see the full set on our custom shoe boxes and footwear packaging page.

What do you need to decide for a custom shoe box?

Five things: the construction (lid-and-base, one-piece, drawer or carry-handle), the board (coated paperboard or corrugated kraft), the print (one colour, full colour, inside print), the finish (foil, emboss, lamination, spot UV) and the box sizes for your size run. Add the box-end label layout and your barcodes, and the factory can make a sample for you to approve.

1. Choose the construction

Lid-and-base (two-piece). The standard retail shoe box. A lid sits over a base, the boxes stack squarely in a stockroom, and the lid is the largest flat surface for your logo. The lid can be printed in a different design from the base, as in the box below, where a navy lid sits on a patterned base.

Two-piece shoe box with a navy lid printed in yellow, sitting on a base printed with a yellow and navy pattern
Lid-and-base box with a contrast-printed base.

One-piece box with an attached lid. The lid is folded from the same blank as the base. It is a good choice when the box may be shipped on its own, because the lid cannot separate in transit. A printed inside lid is easy to add to this style.

Drawer or sleeve. A tray slides out of an outer sleeve. It feels more premium and is often used for rigid or gift boxes, with the sleeve carrying most of the print.

Carry-handle box. A fold-up handle built into the lid lets the box double as a carry bag. It needs a stronger board and a careful dieline, so sample it early.

Shoe box with a full-wrap orange, black and grey print and a fold-up carry handle built into the lid
Carry-handle box with a full-wrap print.

2. Choose the board

Coated paperboard (for example C1S ivory board) has a smooth printing surface. It takes full-colour photographs, fine type and finishes such as hot foil and spot UV. Most printed retail boxes use it.

Corrugated board is stronger and lighter for its strength. In natural kraft it gives a plain, recycled look that suits one or two-colour printing, and it is the usual choice for mailer boxes and outer cartons.

Kraft corrugated shoe box with a large black logo printed across the lid and the long side
Corrugated kraft with a single black print colour.

A simple rule: decide how the box travels first. If every box goes inside an outer carton, printed paperboard is usually enough. If boxes ship singly to consumers, corrugated board or a one-piece construction protects better.

3. Choose the print

One or two spot colours keep the box clean and the colour consistent from run to run. They work especially well on kraft.

Full-colour (CMYK) printing allows photographs and gradients, and can wrap the whole box. Ask for a printed proof, because colour on board never looks exactly like colour on screen.

Inside printing puts a message or colour where the customer sees it on opening. It is a separate print side, so it has to be in the artwork and on the proof.

Open shoe box with a bright orange-red printed interior and white text, navy printed outside
Printed interior: the colour the customer sees on opening.

4. Choose the finish

Finishes are applied after printing and change how a box looks and feels:

  • Hot-foil stamping for metallic logos, often gold or silver on a dark box.
  • Embossing or debossing to raise or press the logo into the board.
  • Matte or gloss lamination to protect the print and change the surface feel.
  • Spot UV to make one area, such as the logo, glossy against a matte box.
Black shoe box with a gold foil monogram framed in a gold square on the lid
Gold foil on a black box.

Each finish adds a step, so keep them to the places the customer will notice: usually the logo on the lid.

5. Small details that matter in use

  • Thumb notch. A cut-out on the side of the base makes the lid easier to lift.
  • Box-end label panel. Leave a clear area on the end of the box for the size, colour and barcode label, so stockroom staff can read it without opening the box.
  • Air or display holes. Some brands add a die-cut hole on the end panel. It has to be in the dieline from the start.
Orange shoe box with a black oval logo on the lid and a thumb notch cut into the side
Thumb notch cut into the side of the base.

6. Size the box to your size run

Box dimensions should come from the actual shoes, not from a standard size chart. The factory measures the samples across your size run and works out a small number of box sizes that cover the whole range, so each pair closes without crushing and without excess empty space. Right-sized boxes also reduce carton volume and freight cost per pair.

If you are adding tissue, a dust bag or a paper insert, size the box with them inside.

7. What to send the factory

  1. Your size run and the shoe style (a sample pair is best).
  2. The construction you want, or a photo of a box you like.
  3. Artwork for every printed side, including the inside if it is printed.
  4. Pantone references for spot colours.
  5. The box-end label layout and your barcode list (UPC or EAN) mapped to each size and colour.
  6. Any market or retailer packaging rules you have to meet.

With these, the factory can return a dieline and a physical sample for approval. Approve a physical proof before mass production; it is the only reliable check of colour and fit.

Tissue, poly bags and hang tags

The box is usually part of a set. Logo tissue wraps the pair inside the box, a printed poly bag or dust bag protects it, and a hang tag carries the brand story and the price or barcode. Specify them together so the set looks consistent. Label and barcode rules are covered in our footwear packaging, labels and barcodes guide, and the EU packaging regulation in the PPWR glossary entry.

DOING supplies custom shoe boxes, tissue, poly bags, dust bags, hang tags and labels as part of its footwear orders, made by specialist packaging factories and packed with your shoes. See the options and real order photos on the custom footwear packaging page.

Frequently asked questions

What is the most common shoe box construction?

The lid-and-base (two-piece) box. A separate lid sits over a base, it stacks well in a stockroom, and the lid gives the largest flat area for your logo. One-piece boxes with an attached lid are the usual alternative when the box also has to survive being shipped on its own.

Should a shoe box be coated paperboard or corrugated kraft?

Coated paperboard (for example C1S ivory board) takes fine print, full-colour images and finishes such as foil and spot UV. Corrugated kraft is stronger and suits a natural, one or two-colour look and boxes that travel without an outer carton. Many brands choose by how the box will be shipped and displayed, then pick the print to suit the board.

How many box sizes do I need for a full size run?

Usually only a few. Box dimensions are worked out from the actual shoes in your size run, and a small number of box sizes normally covers the whole range so that each pair closes without crushing and without too much empty space.

Can the inside of a shoe box be printed?

Yes. Printing the inside of the base or the underside of the lid is a common way to add a message or colour that the customer sees on opening. It is specified as a separate print side, so include it in the artwork and the proof.

Are shoe box materials tested?

The packaging suppliers DOING works with hold SGS test reports for shoe-box board, outer cartons, corrugated liner, hangtags and adhesive labels. The reports are available on request for your compliance file. Whether your market requires them is a question for your importer, and the EU packaging rules are summarised in our PPWR glossary entry.

Sourcing footwear from China?

DOING is a footwear trading & manufacturing partner — OEM/ODM, development, QC and export. Tell us your product, market and MOQ.

Get a Quote
💬
Sourcing Plan WhatsApp Get a Quote